Here's a good looking two-stage seam, the thinnest seam I know, yet also sturdy. Like mattress stitch or grafting, the result is invisible, or nearly so.
![]() |
This two-stage seam is meant for fabrics where the edges are knit on every row, meaning, NOT a slipped selvedge.
(Geek note: For slipped selvedges, work a different one-stage variant called a "valley seam," shown here.)
This isn't a difficult seam: beginners can do it. However, it works best where row-end tension is consistent, meaning, experienced knitters are going to get the best use of this trick.
Knitting machine and loom knitters will also find this handy since those fabrics usually also feature consistent tension. The first stage actually yields the same result as a linker machine. In technical terms, this is a combo link- and top-stitched seam.
![]() |
| Because it is worked 1/2 stitch in from each fabric, the finished seam is slimmed down to a single column on the inside |
A seam hanging by a half-stitch may stress and gape. Therefore, in a second stage, an independent seam is worked from the outside, closing the gap. The manner of working adds practically no bulk, but does beautify and double the strength. Even with the two-stage process, this is a slimmer seam than any other I know, making the work worthwhile, IMHO.
Using poly thread to fasten hand knitting may seem odd. For one thing, it has no stretch. However, this problem is overcome by applying the thread using a stretchy technique, more below.
Another problem with poly thread is strength. Being so very strong, it might cut a tender fiber like cashmere or even merino. However, due to how the second stage lays, the poly thread rarely comes under tension. In this sense the thread is like basting, positioning rather than fastening. However, should great force be applied--a poke from a sharp elbow, perhaps--the poly seam provides strong back-up.
The seam begins by applying the poly thread using a tiny latch hook called a snag catcher or a knit-picker. I've written about these tiny latch hooks before. They are useful to knitters in all kinds of ways (such as preparing zippers for insertion!) On this seam, this tiny latch hook uses the poly thread to fasten the fabrics together, using the slip stitch, which is stretchy.
Slip stitching is a crochet stitch. However, it is identical to the knitted chain bind off, the only difference being, it is worked with a crochet hook in a single motion, rather than with two knitting needles and several motions.
The fact of using slip-stitching means each stitch is made using fresh running thread, as crocheting or knitting stitches are made. This means never having to stop and thread a needle.
In a stockinette fabric, the fabrics are held smooth sides together, reverse stockinette fabric exposed front and back. Insert the latch hook through the OUTERMOST single strand of the fabric facing you, then through the corresponding OUTERMOST single strand of the fabric away from you.
Held sideways for ease of working, the OUTERMOST loop = the TOP strand, as below.
![]() |
| Insert through a single strand from each OUTERMOST (TOP) loop (colorized red) using a tiny latch hook "knit-picker " (aka "snag-catcher"). Then, catch the thread under the hook and draw through. |
Catch up a single loop of poly sewing thread under the hook. For illustration, I used a contrast color (blue). Usually, the thread color matches. However, the thread never actually shows, so use a contrast color if you want to clearly see the thread-path.
Once under the hook, close the latch and pull the thread through the knit fabric. This allows the thread to make a loop over the barrel of the hook, and the slip-stitching proceeds from there. <--This link takes you to a whole post about seaming via slip stitch.
If you prefer video, all of stage-1 is shown in the clip below.
Video clip 1, stage-1
The tension is mild, so that the seam can stretch (somewhat) with the fabric. Turning the fabric 90 degrees makes it easier to work.
Once the fabrics are fastened together with the poly thread, it's on to stage-2.
The seam at the end of stage-1 looks fine from the outside, as long as there's no tension. However, when pulled, the seam gaps, showing a not-very-lovely inside.
In stage-1, one-half of each edge stitch was used up, fastening the fabric together from the inside. In this stage, a BLUNT-nosed sewing needle and a thin color-matched yarn (or a split of the main yarn) fastens the remaining half of each edge stitch together across the gap from the outside.
The needle follows the snakewise path shown by the red dotted line below.
Snaked together like this, the two halves now appear to form a single stitch column from the outside, just as they do on the inside.
![]() |
| Stage-2, a snakewise top seam, applied from the outside. 1/2 stitch + 1/2 stitch fastened together = a whole stitch over the gap |
This goes very fast. The sewing needle need not search for where to insert: the matched half-stitches already abut.
This is applying yarn with a threaded needle, not my fave. However, the yarn is less likely to wear out and get ratty by starting the stage-2 seam at its midpoint. The trick is, leave a tail dangling, long enough to snake together the remaining half-seam. See, starting at the bottom drags all the yarn through each stitch, all the way up. The long yarn snarls, frays, and stretches. Starting in the middle means less yarn dragged through fewer stitches. For the second half, turn the fabric around and set off again. And again, although one doesn't normally begin a sewn-, grafted-, or mattress-stitched seam in the middle for fear of row-mismatch, there's no mismatch problem here: the poly thread pre-positioned the stitches.
Like stage-1, be mild with the tension so the seam neither puckers or zig-zags, but remains as invisible as possible, at the same tension as the surrounding fabric.
If you prefer recordings, here's all of stage-2 in a 6-minute video.
Video clip 2
![]() |
| Bird's eye |





