An urban myth of knitting is that new yarn always ought to be added at the end of a row (side of the fabric) (scroll).
On the one hand, if you are knitting an item to be seamed, this advice can be good (see trick the third, below).
On the other hand, for items where the edge of the knitting is the edge of the garment (scarf, shawl, stole), or for items where you plan to add an edging, this advice is pretty bad. Adding yarn at the end of a row can leave a big loopy gap along one side of your knitting, and/or a lump where the ends are worked in. The side of your work is probably an inconvenient spot for that gap/lump.
Also, advice to put the yarn change in the seam is of little use to circular knitters.
Another myth is that yarn should be "tied in" with a knot. I've ranted elsewhere against knots in knitting--even slip knots, and won't repeat here. I will add, however, that even the tightest knot has the potential to come undone over time with the kind of wear a knitted garment will get.
Anyway--enough about what won't work. Here are three tricks for adding a new ball of yarn.
Trick the first--felting
(fair warning: if you're squeamish, skip straight to trick the second)
(fair warning: if you're squeamish, skip straight to trick the second)
Evidently, the oldest kind of yarn-made fabric is nalbinding. It is made with a large-eyed flat bone-type needle, using short lengths of yarn--originally, the sort of primitive yarn spun by rubbing it between the palms.
Obviously, a major nalbinding issue is how to attach each short length to the next.
Nalbinders solved this problem long ago--maybe in the ice ages--by felting the ends of the yarn together with (this is the squeamy part) spit. Today, most choose to use water, but if you're lazily knitting in bed .... well, just resolve to thoroughly wash your knitting before wearing.
HOW-TO felt the ends
Overlap the ends of the yarn in your hand--by maybe a couple of inches. Add a small amount of the liquid of your choice, and rub the ends between your fingers and your palms or between both palms, until the ends felt. Yup, that's it.
click picture
Of course, the more you practice, the less lumpy the join will be--you can fool with separating the plys in plied yarn before you felt, and fool with the correct amount of liquid, and fool with the rolling action of the felting and fool with the amount of the overlap. However, this isn't rocket science--if cave (wo)men could do it, so can you. A couple of quick experiments will show you the best technique to make the resulting join pretty much invisible in whatever wooly yarn you're using. And of course, by this method, there are no ends to work in.BUT--felting works best on wool--preferably thickish wool. Felting is a poor choice for thin yarns, such as lace, because even the most careful felted join will show against the lacy fabric. And felting works not at all on non-wool yarns. Which brings us to...
Trick the second--overlapping
HOW-TO overlap
Overlap the new end and the old end. Knit THREE stitches with both yarns, then drop the old yarn.
click picture
Be sure there are several inches of EACH end hanging down.
click picture
The overlap may look bulky, but this is temporary.
click picture
Several rows or rounds AFTER the joining, carefully adjust the tension by gently pulling on each end in turn. In heavy work, pull tight enough so that the stitch attached to that end will shrink behind the not-pulled stitch and disappear. In lace work, tug each end carefully only as hard as it takes to make all six overlapped stitches the same size--see photo of lace work below.
click picture
The central stitch, in which both yarns lay unpulled, will be slightly larger than the stitches on either side, but even in loose lacy knitting, where there is little tugging, this join hides.
click picture
If you're working in heavy wool, you clip the ends after you've washed and blocked the garment. Leave a short end (1/2 inch) still sticking out--over time, it will shrink into (and felt onto) the fabric as the garment is pulled and twisted in everyday wear. After several further washings, when you're sure that little tail will shrink no further, you can clip it down as far as the fabric surface with a clear conscience. In woolen lace, where both sides of the fabric are designed to be seen, wash and block the item. When dry, stretch the area of the overlap several times to adjust the tension before clipping the excess very near to the fabric surface.With non-wool yarns, three stitches MIGHT be enough to hold the ends for all times, and it might not, depends how slippery the stuff is. I find that superwash wool, for example, requires more, so I'll sometimes work 4 overlapping stitches. If you have doubts, then use the overlapping method of join PLUS, for insurance, work your ends in further using whatever method you generally use, before you clip the excess. (Working-in ends will be the subject of a future post...)
If there is a pattern to your knitted fabric, think about placing your overlapped stitches there, rather than out in a flat, smooth stockinette stitch area. The 3-stitch-overlapped join is nearly undetectable, but by placing it in a pattern--where the eye is already predisposed to accept a disturbance--you have additional insurance that no one will ever notice.
Trick the third--for items to be seamed
A reader of this blog, Noricum, gets the credit for this trick.For garments which will be seamed (sweaters made in pieces, for example) the idea is to change balls at the side (seam edge) and leave a long tail from the new ball AND the old ball. When the time comes to seam the garment, use the long tails for the sewing yarn--remember to cross the yarns, one going up, and one going down, in such a way as to draw closed the gap where the new ball comes in. Thanks Noricum!
* * *
PS: Here is a link to a post with 10 (!) different methods of working in ends in knitting, eight of which are "as you go."
* * *
--TECHknitter
